PROFESSIONAL RCC BUILDING DESIGN
Comprehensive Training in Structural Analysis, Design & Seismic Detailing
From Engineering Fundamentals to Professional Structural Design Practice
Organized by 3C–Engineering & Research
COURSE OVERVIEW
Reinforced Cement Concrete (RCC) is a composite structural material in which concrete primarily resists compressive stresses, while reinforcing steel provides tensile resistance and improves ductility. The design of RCC buildings requires a thorough understanding of structural behavior, load-resisting mechanisms, material properties, code requirements, and engineering judgment.
The Professional RCC Building Design Course is designed to bridge the gap between academic knowledge and practical structural engineering. It provides comprehensive training in structural analysis, reinforced concrete member design, earthquake-resistant detailing, geotechnical considerations, and foundation engineering.
The course emphasizes manual design calculations, BNBC 2020 and ACI 318 provisions, seismic design principles, and practical applications of CSI ETABS and SAFE.
Participants will work through structural engineering problems and a comprehensive 10-story RCC building analysis to develop the technical competence required for professional design practice.
DETAILED COURSE CURRICULUM
MODULE 01 | Fundamentals of RCC Building Design
- Introduction to Reinforced Concrete Structures and Design Principles.
- Structural Systems, Load Transfer Mechanisms, and Design Philosophy.
- Overview of BNBC 2020 and Applicable ACI 318 Requirements.
- Strength Design Method and Limit State Concepts.
- Structural Safety, Serviceability, Durability, and Constructability.
MODULE 02 | Structural Loading & Seismic Design Criteria
- Dead Loads, Live Loads, and Other Gravity Loads.
- Wind Load Calculation and Structural Response.
- Earthquake Load Calculation and Seismic Design Parameters.
- Gravity and Lateral Load Combinations.
- Equivalent Static Force Procedure.
- Response Spectrum Analysis and Dynamic Analysis Requirements.
- Code-Based Criteria for Selecting Static and Dynamic Analysis Procedures.
- Story Drift, Lateral Displacement, and Serviceability Verification.
- P-Delta Effects and Structural Stability Assessment.
MODULE 03 | Structural Analysis & Building Irregularities
- Fundamental Principles of Structural Analysis and Modeling.
- Classification of Horizontal and Vertical Structural Irregularities.
- Soft Story and Weak Story Identification.
- Torsional and Extreme Torsional Irregularities.
- Mass, Stiffness, and Geometric Irregularities.
- Influence of Structural Irregularities on Seismic Performance.
- Code Requirements and Design Implications for Irregular Buildings.
MODULE 04 | RCC Design Theory & Derivation of Design Equations
- Mechanical Properties and Stress–Strain Relationships of Concrete and Reinforcing Steel.
- Fundamental Assumptions of Reinforced Concrete Design.
- Balanced, Tension-Controlled, and Compression-Controlled Sections.
- Strength Reduction Factors (ϕ) and Their Applications.
- Derivation of Flexural Strength Equations.
- Fundamentals of Axial, Shear, and Torsional Resistance.
- Application of Derived Equations in Practical Structural Design.
MODULE 05 | Analysis & Design of RCC Slabs
- One-Way Slab Analysis and Design.
- Two-Way Slab Analysis and Design.
- Flat Plate Design.
- Flat Slab Design.
- Flexural Strength Verification.
- One-Way and Two-Way (Punching) Shear Checks.
- Deflection Control and Serviceability Requirements.
- Reinforcement Arrangement and Detailing.
MODULE 06 | RCC Beam Design & Seismic Detailing
- Analysis and Design of Singly and Doubly Reinforced Beams.
- Flexural Strength and Reinforcement Calculation.
- Shear Strength Evaluation and Transverse Reinforcement Design.
- Immediate and Long-Term Deflection Checks.
- Combined Shear and Torsion Design.
- Anchorage, Development Length, and Reinforcement Splicing.
- Seismic Design Requirements for Special Moment Frame Beams.
- Reinforcement Confinement and Seismic Detailing.
- Practical Beam Design Calculations.
MODULE 07 | RCC Column Design & Seismic Detailing
- Axially Loaded and Eccentrically Loaded Columns.
- Uniaxial and Biaxial Bending.
- Axial Load–Moment Interaction Diagrams.
- Column Slenderness and Second-Order Effects.
- Column Design under Combined Axial Load and Bending.
- Seismic Design Requirements for Special Moment Frame Columns.
- Strong-Column–Weak-Beam Verification.
- Confinement Reinforcement and Transverse Reinforcement Requirements.
- Anchorage, Lap Splices, and Reinforcement Detailing.
MODULE 08 | Structural Shear Wall & Coupling Beam Design
- Structural Behavior and Seismic Resistance of Shear Walls.
- Shear Wall Analysis under Axial Load, Flexure, and Shear.
- Design Requirements for Special Structural Walls.
- Boundary Element Design and Confinement Detailing.
- Shear Wall Reinforcement Requirements.
- Coupling Beam Analysis and Design.
- Conventional and Diagonal Reinforcement Detailing for Coupling Beams.
- Seismic Performance and Code Compliance.
MODULE 09 | RCC Staircase Design
- Structural Systems and Behavior of Staircases.
- Staircase Load Calculation.
- Waist Slab and Landing Slab Design.
- Flexural and Shear Strength Verification.
- Reinforcement Arrangement, Anchorage, and Detailing.
MODULE 10 | Special Moment Resisting Frame (SMRF) Design
- Seismic Design Philosophy and Ductility Requirements.
- Structural Behavior of Special Moment Resisting Frames.
- Complete Manual Design Calculations for an SMRF.
- Capacity Design Principles for Beams and Columns.
- Strong-Column–Weak-Beam Verification.
- Beam–Column Joint Shear Design.
- Plastic Hinge Formation and Inelastic Structural Behavior.
- Seismic Reinforcement Detailing and Confinement Requirements.
- Code Compliance and Practical Design Considerations.
MODULE 11 | Complete 10-Story RCC Building Analysis Using CSI ETABS
- Development of a Complete Three-Dimensional Structural Model.
- Material Properties and Structural Section Definition.
- Gravity and Lateral Load Assignment.
- Diaphragm Modeling and Mass Source Definition.
- Equivalent Static Earthquake Analysis.
- Modal Analysis and Response Spectrum Analysis.
- Natural Period and Modal Mass Participation Verification.
- Story Displacement and Interstory Drift Checks.
- P-Delta Analysis and Stability Verification.
- Soft Story, Weak Story, and Torsional Irregularity Checks.
- Structural Member Forces and Design Result Interpretation.
- Model Verification and Code-Based Structural Performance Assessment.
- Complete Practical Analysis and Design Review of a 10-Story RCC Building.
MODULE 12 | Geotechnical Engineering for Foundation Design
- Basic Principles of Soil–Structure Interaction.
- Interpretation of Soil Investigation Reports.
- Soil Classification and Engineering Properties.
- Safe and Ultimate Bearing Capacity of Shallow Foundations.
- Foundation Settlement and Serviceability Criteria.
- Axial Load-Carrying Capacity of Piles.
- Selection of Appropriate Foundation Systems Based on Site Conditions.
MODULE 13 | Shallow & Deep Foundation Design
- Isolated Footing Analysis and Design.
- Combined Footing Analysis and Design.
- Pile Foundation Design.
- Pile Group Behavior and Capacity Considerations.
- Pile Cap Analysis, Design, and Reinforcement Detailing.
- Mat/Raft Foundation Analysis and Design.
- Flexural, One-Way Shear, and Punching Shear Verification.
- Foundation Reinforcement Detailing and Constructability Considerations.
MODULE 14 | Foundation Analysis & Design Using CSI SAFE
- Introduction to Foundation Modeling in SAFE.
- Importing Column Loads and Structural Reactions from ETABS.
- Soil Support and Foundation Stiffness Modeling.
- Pile Cap Modeling, Analysis, and Design.
- Mat/Raft Foundation Modeling and Analysis.
- Soil Contact Pressure Evaluation.
- Punching Shear and Flexural Strength Verification.
- Reinforcement Design and Result Interpretation.
- Practical Foundation Design Verification and Code Compliance.
MODULE 15 | Design of Special RCC Structures
- Basement Retaining Wall Analysis and Design.
- Lateral Earth Pressure and Surcharge Load Calculation.
- Hydrostatic Pressure and Groundwater Effects.
- Structural Design of RCC Water Tanks.
- Liquid Pressure, Crack Control, and Serviceability Requirements.
- Reinforcement Detailing for Basement Walls and Water-Retaining Structures.
PRACTICAL TRAINING & DESIGN APPLICATIONS
The course integrates theoretical knowledge with professional engineering applications through:
- Manual Structural Design: Step-by-step design calculations with relevant code references.
- 10-Story Building Project: Complete three-dimensional modeling, equivalent static analysis, and response spectrum analysis using ETABS.
- Earthquake-Resistant Design: Seismic design and detailing of beams, columns, structural walls, and special moment frames.
- Foundation Engineering: Bearing capacity evaluation, pile capacity assessment, and shallow and deep foundation design.
- CSI SAFE Applications: Pile cap and mat foundation analysis, design, and reinforcement verification.
- Engineering Verification: Interpretation of software outputs, independent calculation checks, structural irregularity assessment, and design review.
LEARNING OUTCOMES
Upon completion of the course, participants are expected to develop the ability to:
- Interpret and apply relevant provisions of BNBC 2020 and ACI 318.
- Calculate structural loads and evaluate lateral load effects.
- Perform fundamental RCC member design calculations independently.
- Understand and apply earthquake-resistant structural design principles.
- Develop and evaluate multistory structural models using ETABS.
- Analyze and design common foundation systems using manual methods and SAFE.
- Interpret structural analysis results and recognize potential modeling and design deficiencies.
- Prepare and review code-compliant reinforcement detailing.
The emphasis is on developing engineering judgment, analytical understanding, and practical design proficiency, rather than relying exclusively on software-generated results.
REFERENCE CODES & SOFTWARE
Primary Structural Design References
- Bangladesh National Building Code (BNBC 2020).
- Applicable provisions of ACI 318.
- Relevant structural and geotechnical engineering standards.
Engineering Software
- CSI ETABS — Structural Modeling, Analysis & Design.
- CSI SAFE — Foundation Analy
Curriculum
- 24 Sections
- 26 Lessons
- 50 Weeks
- 0 Items
- Class 11 Item
- Class 21 Item
- Class 31 Item
- Class 41 Item
- Class 54 Items
- Class 61 Item
- Class 71 Item
- Class 82 Items
- Class 91 Item
- Class 101 Item
- Class 110 Items
- Class 12 Column Design1 Item
- Class 13 Shear Wall1 Item
- Class 14 Etabs Output1 Item
- Class 151 Item
- Class 161 Item
- Class 171 Item
- Class 181 Item
- Class 191 Item
- Class 201 Item
- Class 211 Item
- Class 221 Item
- Class 231 Item

I would like to learn RCC design. Please advise
Plz call 01922172825